Large JCV (CNNANT_201910)
Wed, 01/24/2018 - 11:06pm
16 years
|
Would someone keep an eye out for the large JCV, please?
Phil
16 years
|
Would someone keep an eye out for the large JCV, please?
Phil
Thanks!
Large JCV for Re-released CNNANT_2019.10
https://mega.nz/#!tAxwlKbB!7eQFNoOg8wLm3nIU_IMUNT3z-CmDHPv0jWqj6qIfpcY
Password: [our benefactor's moniker]
Size: 830 MiB (870,803,526 bytes)
MD5: 48977dc123f2c679a727bad7ca26fe3f
Much thanks to nandyesc again for sharing his file!
Thanks you so much to you and nandysec again!
Thanks
Thanks nandyesc for the uploads.
rdu
Thank you!
Large JCV for Re-released CNNANT_2019.10
https://mega.nz/#!tAxwlKbB!7eQFNoOg8wLm3nIU_IMUNT3z-CmDHPv0jWqj6qIfpcY
Password: [our benefactor's moniker]
Size: 830 MiB (870,803,526 bytes)
MD5: 48977dc123f2c679a727bad7ca26fe3f
Much thanks to nandyesc again for sharing his file!
Yes, thank you both to nandyesc and tli.
And
My thanks to both also.
nüvi 3590LMT / ecoRouteHD
Hi,have somebody the File
Hi,
have somebody the File D3191250B.jcv ?
thanks
Yes
Hi,
have somebody the File D3191250B.jcv ?
thanks
Yes, read through the earlier posts and you'll see a link to download the file. Remember that this file will only work with the revised 2019.10 City Navigator North America map update.
PS: Welcome to The Factory.
MEGA says the file is not
MEGA says the file is not there?
I see it
MEGA says the file is not there?
When I go to the link, I see the file available for download:
D3060260B .zip
680.1 MB
I see the link has
I see the link has changed.
I have found it.
Thanks.
rdu
Thanks to nandyesc for sharing his file!
Thanks tli and nandyesc
Thanks very much to you both for posting the large JCV file.
The re-release download (2nd download posted in this thread) worked great with my 2019.11 downloaded map.
But I did have to do a hard reset on my device to get the JCV functioning properly. Be sure to backup your temp.gpx file and note all your settings under tools before trying this. Then after restarting your device edit the copied temp.gpx file making no changes and save it so the date of the file changes. Then copy it back to your device and power on normally. Your favorites will be restored and routes can be re-imported. Then check your settings and manually change where needed.
Power down, reboot?
Thanks very much to you both for posting the large JCV file.
The re-release download (2nd download posted in this thread) worked great with my 2019.11 downloaded map.
But I did have to do a hard reset on my device to get the JCV functioning properly...
It's good to hear all worked for you. I wonder, though, if the hard reset was needed. Given that so many devices now enter a sleep mode rather than turning off, did you try a power down and reboot first? It may just have taken a reboot for the device to relocate the jcv file. I don't know what device you have but holding the power off switch until you see a power down warning, then OKing the power down is pretty common for Garmins. I don't know if a power down would be sufficient but I would have tried it before going to a hard reset.
Sleep mode.
CraigW, I am not 100% sure about this, but I think plugging your device into the computer in Mass Storage mode kills the sleep mode and the next boot up will be a full power cycle boot up. I suppose even if that is correct though, it would be possible to install the large JCV file using a SD card reader, so the device could still be in sleep mode.
Alan - Android Auto, DriveLuxe 51LMT-S, DriveLuxe 50LMTHD, Nuvi 3597LMTHD, Oregon 550T, Nuvi 855, Nuvi 755T, Lowrance Endura Sierra, Bosch Nyon
Thanks
Thank you nandyes
Thanks!
For this service to the community!
Ted - Garmin Nuvi 1450 LM
Power Down, Reboot?
Thanks very much to you both for posting the large JCV file.
The re-release download (2nd download posted in this thread) worked great with my 2019.11 downloaded map.
But I did have to do a hard reset on my device to get the JCV functioning properly...
It's good to hear all worked for you. I wonder, though, if the hard reset was needed. Given that so many devices now enter a sleep mode rather than turning off, did you try a power down and reboot first? It may just have taken a reboot for the device to relocate the jcv file. I don't know what device you have but holding the power off switch until you see a power down warning, then OKing the power down is pretty common for Garmins. I don't know if a power down would be sufficient but I would have tried it before going to a hard reset.
@CraigW
I did do a soft reset which did not fix my problem.
But I think I know what happened. After installing a new map and large JCV I switch to the new map and run a test Route I keep on my device. It didn't work. What I needed to do was to recalculate the route with the new map. I think that would have fixed the problem.
Doing the hard reset forced me to reinstall my routes which were then recaluated when I imported them.
I need to remember to recalc routes when switching between maps or installing a new map.
Thanks for your comments.
Thanks
Thanks
Garmin Nuvi 1490LMT, Nuvi 750, Nuvi 255LT
Thanks
for making the large JCV file available for download.
Only works in my ancient 855 and only updated the 2019.11 map file today via the cloning method.
Nuvi 2797LMT, DriveSmart 50 LMT-HD, Using Windows 10. DashCam A108C with GPS.